Sep-2023 Download Free Latest Exam NACE-CIP1-001 Certified Sample Questions
Prepare for your exam certification with our NACE-CIP1-001 Certified NACE
NACE-CIP1-001 Coating Inspector Level 1 certification is a globally recognized qualification that assesses an individual’s knowledge and practical skills in the field of coating inspection. Coating Inspector Level 1 certification is offered by the National Association of Corrosion Engineers (NACE), a professional organization dedicated to advancing the corrosion control industry. The NACE-CIP1-001 certification is the first level of the NACE Coating Inspector program and is designed for individuals who have a basic understanding of coating inspection.
NEW QUESTION # 41
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Permit coating to take place so as not to lose the blast
- C. Review the relevant standard with the Contractor
- D. Call your supervisor
Answer: C
NEW QUESTION # 42
Which of these tests uses a syringe?
- A. Potassium ferricyanide
- B. Sleeve test
- C. Bresle patch
- D. Soluble salts meter
Answer: C
NEW QUESTION # 43
Checking is
- A. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- B. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- C. an exposed area of the substrate or previous coat material, caused by poor application technique.
- D. a fine crack in the surface of a coating that rarely reaches the substrate
Answer: D
NEW QUESTION # 44
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. No, because there is no real difference in the standards
- B. It depends on which hand tool the Contractor selects
- C. Yes, because the 'two standards are not equivalent
- D. It depends on which power tool the Contractor selects
Answer: A
NEW QUESTION # 45
Most industrial coatings are:
- A. Organic
- B. Inorganic
- C. Resistant to temperatures above 200C
- D. Resistant to concentrated sulfuric acid
Answer: A
NEW QUESTION # 46
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will make a meaningful technical contribution to the job
- B. a) and c)
- C. The Inspector will improve job flow and schedule
- D. The inspection cost will be offset by an improvement in service life
Answer: B
NEW QUESTION # 47
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. Subjective comments re ding the application team
- C. Objective comments regarding the application work
- D. The inspector's personal opinions of the application team
Answer: A
NEW QUESTION # 48
Which is a component that supplies most of the features and functions of the material?
- A. solvent
- B. binder
- C. pigment
- D. additive
Answer: B
NEW QUESTION # 49
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Condition H
- B. Rust Grades A-D
- C. Surface Conditions E-G
- D. Rust Grades 1-4
Answer: B
NEW QUESTION # 50
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. Low Relative Humidity
- C. Low Surface Temperature
- D. High Surface Temperature
Answer: B
NEW QUESTION # 51
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to saturation level.
Answer: D
NEW QUESTION # 52
The initial steel condition is important to the NACE Inspector because:
- A. Less abrasive is need if the mill Scale s gone
- B. If the steel is pitted more coating will be required
- C. The Inspector may have to reject the Steel
- D. It affects the final appearance after blasting
Answer: C
NEW QUESTION # 53
NACE SP 0178 is a standard for:
- A. Structural steel to be coated for Atmospheric Service
- B. Tanks and Vessels to, be Lined for Immersion Service
- C. Stainless steel pipe to be Externally Coated
- D. Tanks and Vessels to be Externally Coated
Answer: B
NEW QUESTION # 54
Removal of surface contaminants is done by:
- A. A combination of methods
- B. Waterjetting
- C. Scarifying
- D. Abrasive blasting
Answer: A
NEW QUESTION # 55
The NACE Inspector should perform tests for soluble salts:
- A. Prior to coating application
- B. After surface preparation
- C. Prior to surface preparation
- D. When specified
Answer: D
NEW QUESTION # 56
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Use another method as the comparator method is too subjective
- C. Record the segment with the less aggressive profile
- D. Record your result by identifying two segments
Answer: C
NEW QUESTION # 57
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Always typewritten
- C. Always handwritten
- D. Submitted before the end of the job
Answer: A
NEW QUESTION # 58
......
NACE-CIP1-001 certification exam is a comprehensive assessment that covers a wide range of topics related to coating inspection. NACE-CIP1-001 exam consists of 100 multiple-choice questions that must be completed within a four-hour time frame. The questions are designed to test the candidate's understanding of coating materials, surface preparation, coating application, and inspection techniques.
Free NACE NACE-CIP1-001 Exam 2023 Practice Materials Collection: https://www.testkingfree.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
NACE-CIP1-001 Exam Info and Free Practice Test All-in-One Exam Guide Sep-2023: https://drive.google.com/open?id=1VbY1qXzZwR931cRLRDHkMtgK-7C-yMA3