View NACE-CIP1-001 Exam Question Dumps With Latest Demo [Sep 25, 2022]
Free NACE-CIP1-001 Test Questions Real Practice Test Questions
Do you know anything about the NACE-CIP1-001 Exam?
NACE CIP Level 1 is an industry-recognized certification program. It allows individuals to obtain a certificate that certifies them as knowledgeable and competent coatings inspectors. It is the first step towards becoming a Certified Professional Coatings Inspector. The NACE CIP1-001 exam is a good way to show your ability to inspect the coating industry. The NACE-CIP1-001 exam is a challenging test. The candidate must be well prepared in order to crack the NACE-CIP1-001 exam. Purchase is NACE-CIP1-001 Dumps and save your time. Tank lining is a crucial aspect of any industrial plant. For the safety of the workers, it is very important to use the best lining materials.
NEW QUESTION 48
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Hire a third patty to assist you in understanding the document
- B. Carefully review the document and do the best you can
- C. Advise the owners' representative of your lack of knowledge in this area
- D. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
Answer: B
NEW QUESTION 49
The least effective method of surface cleaning is most likely
- A. water blasting.
- B. hand tool cleaning.
- C. dry grit blasting.
- D. power tool cleaning.
Answer: B
NEW QUESTION 50
Relative humidity is
- A. a measure of the amount of moisture in the air compared to saturation level.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. the highest temperature at which moisture forms on a steel surface.
Answer: A
NEW QUESTION 51
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. High Surface Temperature
- C. Low Surface Temperature
- D. Low Relative Humidity
Answer: D
NEW QUESTION 52
Stripe coats are generally applied to:
- A. Complex geometric shapes
- B. a), b), and c)
- C. Welds
- D. Edges and corners
Answer: B
NEW QUESTION 53
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A general guide
- B. Pass/fail criteria
- C. A method to grade surface profile
- D. A final conflict resolution method
Answer: A
NEW QUESTION 54
Polymerization is the process of:
- A. Monomers joining together
- B. All organic coatings
- C. Monomers telegraphing
- D. All thermoplastic coatings
Answer: A
NEW QUESTION 55
Daily reports are important because:
Select All That Apply
- A. The information aids communication with supervisors.
- B. Inspectors rarely change on a project.
- C. the information impacts future projects.
- D. Management uses them to make personnel decisions.
Answer: A,C,D
NEW QUESTION 56
Which one of the following documents is the best source for coating technical data:
- A. Safety Data Sheet;
- B. Technical Data Sheet
- C. Application Guidelines
- D. Specification
Answer: B
NEW QUESTION 57
ISO SA 2 is defined as:
- A. Light Blast Cleaning
- B. Thorough Blast Cleaning
- C. Near White Metal Blasting
- D. Very Thorough Blast Cleaning
Answer: B
NEW QUESTION 58
Galvanic corrosion occurs on which of the following substrates:
- A. Fiberglass Reinforced Plastic
- B. Wood
- C. Concrete
- D. Metal
Answer: D
NEW QUESTION 59
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. alligatoring.
- B. checking.
- C. cracking.
- D. blistering.
Answer: B
NEW QUESTION 60
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. In the office only
- B. Only if the specification requires it
- C. In the field only
- D. At all times
Answer: D
NEW QUESTION 61
Digital hygrometers
- A. determine relative humidity, air temperature, and dew point temperature:
- B. use a thermocouple in contact with the surface to measure temperature
- C. are used to measure temperature from a distance.
- D. consist of a bimetallic sensing element protected from wind gusts.
Answer: A
NEW QUESTION 62
Removal of welds splatter is required:
- A. On every job
- B. When NACE/SSPC abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. When ISO abrasive blast standards are specified
Answer: C
NEW QUESTION 63
According to SSPC PA 2 a Spot Measurement is:
- A. The average of all spot measurements in a given area
- B. The overall average of all readings
- C. The average of gauge readings taken in a 4cm (1.5 inch) circle
- D. A single gauge reading
Answer: C
NEW QUESTION 64
A magnetic pull-off type gauge is a good choice when:
- A. When an intrinsically safe tool is required
- B. Accuracy is not required
- C. When working on non-ferrous metals
- D. Performing an adhesion test
Answer: A
NEW QUESTION 65
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will improve job flow and schedule
- B. The inspection cost will be offset by an improvement in service life
- C. a) and c)
- D. The Inspector will make a meaningful technical contribution to the job
Answer: C
NEW QUESTION 66
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Use the job specification as a guide
- B. Call the person who wrote the specification for clarification
- C. Use the product data sheet as a guide
- D. Call the coating manufacturer for clarification
Answer: A
NEW QUESTION 67
Surface profile describes:
- A. The initial condition of the surface prior to abrasive blasting
- B. The level of surface cleanliness required after abrasive blasting
- C. The level of surface roughness required after abrasive blasting
- D. The general condition of the surface required after abrasive blasting
Answer: C
NEW QUESTION 68
The NACE Inspector should perform tests for soluble salts:
- A. When specified
- B. After surface preparation
- C. Prior to coating application
- D. Prior to surface preparation
Answer: A
NEW QUESTION 69
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Rust Grades 1-4
- C. Surface Condition H
- D. Surface Conditions E-G
Answer: A
NEW QUESTION 70
SSPC SP 1 identifies the use of:
- A. A wide variety of materials
- B. Organic solvents
- C. Inorganic solvents
- D. Biodegradable detergents
Answer: A
NEW QUESTION 71
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. scratches the surface too deeply resulting in uneven coating application
- B. damages structural elements thereby speeding up the corrosion process.
- C. develops a polished surface, which is a poor anchor profile for most coatings
- D. develops a good anchor profile resulting in uneven coating application.
Answer: C
NEW QUESTION 72
......
The salary of a NACE CIP1-001 certified professional can be found here.
The Average salary of different countries of NACE CIP1-001 Certified professionals is given below:
- UK 49527.40 Pounds
- USA 67,000 USD
- India 4982421.50 INR
The certification path of the NACE CIP1-001 exam is explained here.
You can get a certification if you pass the NACE CIP1-001 exam. You should not take a risk while choosing the NACE CIP1-001 certification. We are offering you the best NACE CIP1-001 exam dumps. The NACE CIP1-001 exam is designed by experienced professionals. They have written different kinds of questions on the topic related to the NACE CIP1-001 exam.
View All NACE-CIP1-001 Actual Free Exam Questions Updated: https://www.testkingfree.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
NACE-CIP1-001 Dumps Updated Sep 25, 2022 WIith 100 Questions: https://drive.google.com/open?id=1WZz0OmzbcAMFdxVNowyNuZhcvUuOigSu