NSE4_FGT-7.0 Actual Questions 100% Same Braindumps with Actual Exam!
NSE4_FGT-7.0 Study Material, Preparation Guide and PDF Download
The Fortinet NSE4_FGT-7.0 Certification Exam tests a candidate's ability to configure and manage FortiGate devices, including firewall policies, VPNs, user authentication, and traffic shaping. It also covers advanced topics such as high availability, web filtering, and application control. The exam consists of 60 multiple-choice questions and has a time limit of 120 minutes. To pass the exam, candidates must achieve a minimum score of 70%.
NEW QUESTION # 31
Refer to the exhibit.
Based on the raw log, which two statements are correct? (Choose two.)
- A. Traffic is blocked because Action is set to DENY in the firewall policy.
- B. Traffic belongs to the root VDOM.
- C. Log severity is set to error on FortiGate.
- D. This is a security log.
Answer: A,D
NEW QUESTION # 32
What inspection mode does FortiGate use if it is configured as a policy-based next-generation firewall (NGFW)?
- A. Flow-based inspection
- B. Certificate inspection
- C. Proxy-based inspection
- D. Full Content inspection
Answer: A
Explanation:
The default mode is flow based for the policies. NGFW mode does not change the inspection mode.
NEW QUESTION # 33
Which statements about the firmware upgrade process on an active-active HA cluster are true? (Choose two.)
- A. Uninterruptable upgrade is enabled by default.
- B. Traffic load balancing is temporally disabled while upgrading the firmware.
- C. The firmware image must be manually uploaded to each FortiGate.
- D. Only secondary FortiGate devices are rebooted.
Answer: A,B
NEW QUESTION # 34
Which two statements are true about collector agent standard access mode? (Choose two.)
- A. Standard access mode supports nested groups.
- B. Standard mode security profiles apply to organizational units (OU).
- C. Standard mode uses Windows convention-NetBios: Domain\Username.
- D. Standard mode security profiles apply to user groups.
Answer: C,D
NEW QUESTION # 35
An administrator must disable RPF check to investigate an issue.
Which method is best suited to disable RPF without affecting features like antivirus and intrusion prevention system?
- A. Disable the RPF check at the FortiGate interface level for the source check.
- B. Disable the RPF check at the FortiGate interface level for the reply check.
- C. Enable asymmetric routing, so the RPF check will be bypassed.
- D. Enable asymmetric routing at the interface level.
Answer: A
NEW QUESTION # 36
An administrator has a requirement to keep an application session from timing out on port 80. What two changes can the administrator make to resolve the issue without affecting any existing services running through FortiGate? (Choose two.)
- A. Create a new firewall policy with the new HTTP service and place it above the existing HTTP policy.
- B. Set the session TTL on the HTTP policy to maximum
- C. Set the TTL value to never under config system-ttl
- D. Create a new service object for HTTP service and set the session TTL to never
Answer: C,D
NEW QUESTION # 37
Refer to the exhibit.
According to the certificate values shown in the exhibit, which type of entity was the certificate issued to?
- A. A bridge CA
- B. A root CA
- C. A subordinate
- D. A user
Answer: D
NEW QUESTION # 38
Refer to the exhibit.
The exhibit contains a network diagram, virtual IP, IP pool, and firewall policies configuration.
The WAN (port1) interface has the IP address 10.200.1.1/24.
The LAN (port3) interface has the IP address 10 .0.1.254. /24.
The first firewall policy has NAT enabled using IP Pool.
The second firewall policy is configured with a VIP as the destination address.
Which IP address will be used to source NAT the internet traffic coming from a workstation with the IP address 10.0.1.10?
- A. 10.200.1.10
- B. 10.200.1.1
- C. 10.200.1.100
- D. 10.200.3.1
Answer: C
NEW QUESTION # 39
An administrator observes that the port1 interface cannot be configured with an IP address. What can be the reasons for that? (Choose three.)
- A. The interface is a member of a zone.
- B. Captive portal is enabled in the interface.
- C. The operation mode is transparent.
- D. The interface is a member of a virtual wire pair.
- E. The interface has been configured for one-arm sniffer.
Answer: C,D,E
Explanation:
https://help.fortinet.com/fos50hlp/54/Content/FortiOS/fortigate-whats-new-54/Top_VirtualWirePair.htm
NEW QUESTION # 40
Refer to the exhibit.
The exhibit contains the configuration for an SD-WAN Performance SLA, as well as the output of diagnose sys virtual-wan-link health-check.
Which interface will be selected as an outgoing interface?
- A. port4
- B. port1
- C. port2
- D. port3
Answer: B
Explanation:
Port 1 shows the lowest latency.
NEW QUESTION # 41
Refer to the exhibit.
The exhibit contains a network diagram, firewall policies, and a firewall address object configuration.
An administrator created a Deny policy with default settings to deny Webserver access for Remote-user2. Remote-user2 is still able to access Webserver.
Which two changes can the administrator make to deny Webserver access for Remote-User2? (Choose two.)
- A. Disable match-vip in the Deny policy.
- B. Set the Destination address as Deny_IP in the Allow-access policy.
- C. Set the Destination address as Web_server in the Deny policy.
- D. Enable match vip in the Deny policy.
Answer: C,D
NEW QUESTION # 42
Examine the two static routes shown in the exhibit, then answer the following question.
Which of the following is the expected FortiGate behavior regarding these two routes to the same destination?
- A. FortiGate will load balance all traffic across both routes.
- B. FortiGate will use the port1 route as the primary candidate.
- C. FortiGate will route twice as much traffic to the port2 route
- D. FortiGate will only actuate the port1 route in the routing table
Answer: B
Explanation:
Explanation
"If multiple static routes have the same distance, they are all active; however, only the one with the lowest priority is considered the best path."
NEW QUESTION # 43
Refer to the exhibit.
The exhibits show a network diagram and the explicit web proxy configuration.
In the command diagnose sniffer packet, what filter can you use to capture the traffic between the client and the explicit web proxy?
- A. 'host 192.168.0.2 and port 8080'
- B. 'host 10.0.0.50 and port 8080'
- C. 'host 192.168.0.1 and port 80'
- D. 'host 10.0.0.50 and port 80'
Answer: A
NEW QUESTION # 44
Which three methods are used by the collector agent for AD polling? (Choose three.)
- A. WMI
- B. Novell API
- C. NetAPI
- D. WinSecLog
- E. FortiGate polling
Answer: A,C,D
Explanation:
Reference: https://kb.fortinet.com/kb/documentLink.do?externalID=FD47732
NEW QUESTION # 45
Refer to the exhibit.
Given the security fabric topology shown in the exhibit, which two statements are true? (Choose two.)
- A. This security fabric topology is a logical topology view.
- B. Device detection is disabled on all FortiGate devices.
- C. There are 19 security recommendations for the security fabric.
- D. There are five devices that are part of the security fabric.
Answer: A,C
Explanation:
References:
https://docs.fortinet.com/document/fortigate/5.6.0/cookbook/761085/results
https://docs.fortinet.com/document/fortimanager/6.2.0/new-features/736125/security-fabric-topology
NEW QUESTION # 46
Which CLI command allows administrators to troubleshoot Layer 2 issues, such as an IP address conflict?
- A. get system status
- B. diagnose sys top
- C. get system performance status
- D. get system arp
Answer: D
Explanation:
Explanation
"If you suspect that there is an IP address conflict, or that an IP has been assigned to the wrong device, you may need to look at the ARP table."
NEW QUESTION # 47
Examine the network diagram shown in the exhibit, then answer the following question:
Which one of the following routes is the best candidate route for FGT1 to route traffic from the Workstation to the Web server?
- A. 172.16.0.0/16 [50/0] via 10.4.200.2, port2 [5/0]
- B. 0.0.0.0/0 [20/0] via 10.4.200.2, port2
- C. 172.16.32.0/24 is directly connected, port1
- D. 10.4.200.0/30 is directly connected, port2
Answer: C
NEW QUESTION # 48
Examine the IPS sensor and DoS policy configuration shown in the exhibit, then answer the question below.
When detecting attacks, which anomaly, signature, or filter will FortiGate evaluate first?
- A. IMAP.Login.brute.Force
- B. Location: server Protocol: SMTP
- C. SMTP.Login.Brute.Force
- D. ip_src_session
Answer: A
NEW QUESTION # 49
Refer to the exhibits.
Exhibit A shows system performance output. Exhibit B shows a FortiGate configured with the default configuration of high memory usage thresholds. Based on the system performance output, which two statements are correct? (Choose two.)
- A. FortiGate has entered conserve mode.
- B. Administrators cannot change the configuration.
- C. Administrators can access FortiGate only through the console port.
- D. FortiGate will start sending all files to FortiSandbox for inspection.
Answer: A,B
NEW QUESTION # 50
An administrator wants to configure Dead Peer Detection (DPD) on IPSEC VPN for detecting dead tunnels. The requirement is that FortiGate sends DPD probes only when no traffic is observed in the tunnel.
Which DPD mode on FortiGate will meet the above requirement?
- A. Enabled
- B. Disabled
- C. On Idle
- D. On Demand
Answer: C
NEW QUESTION # 51
......
NSE4_FGT-7.0 Certification Study Guide Pass NSE4_FGT-7.0 Fast: https://www.testkingfree.com/Fortinet/NSE4_FGT-7.0-practice-exam-dumps.html
Free NSE4_FGT-7.0 Certification Sample Questions with Online Practice Test: https://drive.google.com/open?id=1Pg6vthU-ylm6q5dCkCz6rgnXs1C-VUbw