[Jan 04, 2022] Fully Updated Dumps PDF - Latest NS0-194 Exam Questions and Answers
100% Free NS0-194 Exam Dumps to Pass Exam Easily from TestKingFree
NEW QUESTION 85
A customer has replaced both interconnect cables on a FAS3240 HA pair with IOXM because they were damaged. After replacing the cables, the customer receives the error shown below.
"HA interconnect port 1 of this appliance seems to be connected to port 2 on the partner appliance." In this scenario what is the cause of this error?
- A. The interconnects are cross-cabled, you must connect c0a with c0a and c0b with c0b.
- B. c0a and c0b are 10Gbit Ethernet ports which must not be used for the interconnect.
- C. You must issue the if config down . . . command followed by the if config up ... command for both ports, on both controllers, after replacing the cables.
- D. The interconnect cables must not be replaced while the controllers are up and running.
Answer: A
NEW QUESTION 86
How many drive bays does a DS4246 shelf have?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 87
Click the Exhibit button. Your customer explains that his disks are showing 100% utilization, but he does not see very much user I/O. While investigating, you collect statistics using the statit command over a 10-second time period as shown in the exhibit.
In this scenario, what is the problem?
- A. The end users are doing a lot of reads on the SATA disks using VAAI, which does not show up as user I/O.
- B. Disk 0a.16 is faulty, indicated by the high latency for ureads, and should be replaced.
- C. Disk 0a.16 is being used to reconstruct data from a failed disk in the aggregate.
- D. The network has too many multicast packets, which means the data is not being sent out over the network correctly.
Answer: A
NEW QUESTION 88
You are using AFF storage with the NVMe storage protocol on your Linux clients.
In this scenario, which NVMe feature must be present and enabled for the client to see storage failover happen?
- A. NVMe Qualified Name (NQN)
- B. Asymmetric Namespace Access (ANA)
- C. Asymmetric Logical Unit Access (ALUA)
- D. Multi-Path I/O (MPIO)
Answer: D
NEW QUESTION 89
Referring to the exhibit.
Your customer's MetroCluster controllers have generated AutoSupport notifications with a "DISK REDUNDANCY FAILED" message.
Referring to the exhibit, which component is causing the problem?
- A. the SAN switch sitel_2
- B. the SAN switch site3_3
- C. the ATTO bridges on site3
- D. the inter-switch link (ISL) between site1 and site3
Answer: D
NEW QUESTION 90
Exhibit:
Your customer has recently migrated from their FAS3140 system running Data ONTAP 7.3.7 to a FAS2552 system running Data ONTAP 8.2.3 7-Mode through the head upgrade process.
They are no longer receiving the weekly AutoSupport notifications and want to know why. The exhibit shows the AutoSupport options from the nodes that have the same settings.
In this scenario, which solution is correct?
- A. There is no reason on the FAS2552 side why the customer should not receive the AutoSupport notifications. They should investigate their mail server to troubleshoot this issue.
- B. In Data ONTAP 8.2, weekly AutoSupport notifications are no longer sent to all recipients to reduce the mail load. The customer should add their e-mail address to the autosupport. partner. to option.
- C. In Data ONTAP 8.2, weekly AutoSupport notifications are no longer sent to the autosupport.to recipient, but only to autosupport.partner.to and to autosupport.support.to. The customer needs to add their e-mail address to one of these options.
- D. In Data ONTAP 8.2, the protocol for AutoSupport is changed to HTTPS by default, so the customer must have an HTTPS destination for the AutoSupport data.
Answer: C
NEW QUESTION 91
Which CIFS server configuration determines the domain controllers that a CIFS server uses?
- A. enabled SMB versions
- B. site membership
- C. discovery mode
- D. trusted domains
Answer: B
NEW QUESTION 92
While troubleshooting intermittent takeover impossible command entries on the console, you request the output of the storage failover interconnect statistics error show command.
Which two counters would help troubleshoot this problem? (Choose two.)
- A. sent queue length counter
- B. link error recovery counter
- C. avg peer connection time
- D. peer connections lost
Answer: A,B
NEW QUESTION 93
Your storage system has experienced a double-disk failure. When is this scenario considered to be in double-degraded mode?
- A. when two disks failed on a single disk shelf
- B. when two disks failed on a single aggregate
- C. when two disks failed on a node
- D. when two disks failed in a single RAID group
Answer: D
NEW QUESTION 94
While troubleshooting client access issues to a CIFS share, you notice that the issue only occurs when the data LIF that the clients are accessing is on a specific node in the cluster.
In this scenario, which configuration should you review to determine why this issue is happening?
- A. Kerberos
- B. export policies
- C. share path
- D. cluster health
Answer: A
NEW QUESTION 95
You are creating a disk-partitioned root aggregate.
Which two rules are enforced automatically when accomplishing this task? (Choose two.)
- A. The only supported RAID type for aggregates containing root-data partitioned disks is RAID-DP.
- B. The only supported RAID type for aggregates containing root-data partitioned disks is RAID 4.
- C. A RAID group can have more than one partition from the same disk.
- D. A RAID group cannot have more than one partition from the same disk.
Answer: A,D
NEW QUESTION 96
Referring to the exhibit.
A storage administrator tells you that a company security mandate was applied to remove all CIFS share level permissions of everyone - full control. Now users are unable to access CIFS shares.
The storage virtual machine (SVM) is named "SVM1" on clustered Data ONTAP 8.3.1. The storage administrator wants to know what can be done to restore full control access to users that are receiving "access denied" errors.
The storage administrator has provided you with the vserver cifs share show command output of one of the CIFS shares with issues as shown in the exhibit.
Which two steps must you perform to solve the problem? (Choose two.)
- A. Ensure that, in Active Directory, the desired users are members of the domainA\companyusers group.
- B. Ensure that, in Active Directory, the desired users are members of the domainA \temps group.
- C. Execute the ::> vserver cifs share access-control delete -vserver SVM1 -share test9 - user-or-group domainA \lnterngroup command from the controller.
- D. Execute the ::> vserver cifs share access-control delete -vserver SVM1 -share test9 - user-or-group Everyone command from the controller.
Answer: A,C
NEW QUESTION 97
As part of your backup policy, you configured a local snapshot schedule on your production volume. You review the list of Snapshot copies and you do not see a snapshot from last night.
What are two causes for this problem? (Choose two.)
- A. The volume had 255 Snapshot copies.
- B. Snapshot autodelete is enabled
- C. The volume snapshot reserve was decreased.
- D. A storage takeover happened.
Answer: A,B
NEW QUESTION 98
A customer fails to see any disks in SnapDrive for Windows but they do see them in File Explorer. Which two statements describe what you should do to solve this problem? (Choose two.)
- A. Restart the SnapDrive for Windows service.
- B. Verify that the transport protocol is set to HTTPS.
- C. Unmap and map all the LUNs back to the Windowsmachine.
- D. Perform a rescan from the Disk Management MMC.
Answer: A,D
NEW QUESTION 99
What are two conditions that would cause writes in memory to be written to disk? (Choose two.)
- A. A user presses "Save".
- B. A Snapshot copy is taken.
- C. Drive capacity becomes available.
- D. The NVRAM (NVLog) fills up.
Answer: A,D
NEW QUESTION 100
Referring to the exhibit.
A customer contacts you and asks for assistance in determining which ports can be used for a new broadcast domain on a clustered Data ONTAP 8.3.2 system.
The system is serving LUNs using the FC protocol and is in production.
However, for Ethernet traffic, it is not yet in production. The customer provides you the output of the network port show command.
Referring to the exhibit, which ports will be eligible to create a new broadcast domain without impacting production storage virtual machines (SVMs) serving FC LUNs?
- A. any port in the Default broadcast domain on node1 and node2
- B. any port on node2
- C. any port on model
- D. any port in the cluster broadcast domain on node1 and node2
Answer: A
NEW QUESTION 101
A large amount of data was deleted from a volume. After a few hours, the space was still not available to NFS clients accessing the volume.
What are two reasons that would account for this problem? (Choose two.)
- A. There is a thick-provisioned LUN in the volume.
- B. The client needs to re-scan the volume to detect the changes.
- C. The volume contains Snapshot copies that were taken before the data was deleted.
- D. The deleted data was all deduplicated data.
Answer: B,C
NEW QUESTION 102
A user can read and write some files on an NFS volume, but the user is unable to read all of the files in the volume.
In this scenario, which command will help you troubleshoot this problem?
- A. security audit show
- B. vserver security trace filter create
- C. vserver export-policy check-access
- D. security login create
Answer: B
Explanation:
Explanation/Reference:
NEW QUESTION 103
Referring to the exhibit.
A customer is attempting to protect the source volume listed in the exhibit. They try to initialize a DP mirror relationship to the destination volume but it will not initialize as expected.
Which two settings on the destination volume are causing this problem? (Choose two.)
- A. max-autosize
- B. volume size
- C. type
- D. language
Answer: A,C
NEW QUESTION 104
Referring to the exhibit.
The exhibit shows an overview of a customer's network design. The customer is experiencing ping loss. As part of the troubleshooting process, you receive output by using the if grp status command from the node shell.
In this scenario, what is the customer's problem?
- A. Link aggregation is not active on the switch, despite being in the design.
- B. Virtual LANs (VLANs) are not used, which causes the interfaces to be overloaded.
- C. Virtual interface (VIF) is deprecated in clustered Data ONTAP because the interface group is not working as it should.
- D. The interface group on the controller is not using the default type, causing a connection mismatch with the switch.
Answer: C
NEW QUESTION 105
Which two statements describe ONTAP NVRAM? (Choose two.)
- A. ONTAP NVRAM stores uncommitted writes.
- B. ONTAP NVRAM is battery backed.
- C. ONTAP NVRAM is used as write cache.
- D. ONTAP NVRAM is used as read cache.
Answer: A,C
NEW QUESTION 106
You need to provide a customer an action plan to update an ONTAP system after a security bulletin has been issued.
In this scenario, how do you accomplish this task?
- A. Review the ONTAP 9 product page.
- B. Download the target version and do a pre-check.
- C. Use Upgrade Advisor on Active IQ.
- D. Use the Interoperability Matrix Tool.
Answer: B
NEW QUESTION 107
You want to map an iSCSI LUN from a NetApp controller.
Which two components are required to accomplish this task? (Choose two.)
- A. FCP zoning
- B. igroup
- C. initiator WWPN
- D. iSCSI initiator
Answer: A,C
NEW QUESTION 108
A customer receives the message shown below in their EMS logs.
Tue Jun 27 18:34:18 CEST
[netapp-ct1: cp_worker: wafl.cp.toolong:error]: Aggregate AG1_NTAP_PROD experienced a long CP.
Tue Jun 27 18:37:10 CEST
Which two data sources do you use to explain this message? (Choose two.)
- A. mgwd.log
- B. Active IQ Unified Manager
- C. Performance Archive
- D. ONTAP System Manager
Answer: C,D
NEW QUESTION 109
......
Network Appliance NS0-194 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
| Topic 8 |
|
| Topic 9 |
|
NetApp NS0-194 Exam Certification Details:
| Passing Score | 63% |
| Number of Questions | 60 |
| Recommended Training | Introduction to NetApp Storage System Basic Components (WBT) Introduction to Clustered Data ONTAP Architecture (WBT) Introduction to Aggregates and FlexVols in Clustered Data ONTAP (WBT) Introduction to Networking in Clustered Data ONTAP (WBT) Introduction to High-Availability in Clustered Data ONTAP (WBT) Introduction to Data Protection in Clustered Data ONTAP (WBT) |
| Exam Name | Support Engineer |
| Exam Registration | PEARSON VUE |
| Exam Price | $150 USD |
| Sample Questions | NetApp NS0-194 Sample Questions |
| Exam Code | NS0-194 NCSE |
| Duration | 90 minutes |
Free NS0-194 Exam Questions NS0-194 Actual Free Exam Questions: https://www.testkingfree.com/NetworkAppliance/NS0-194-practice-exam-dumps.html
Verified NS0-194 dumps and 190 unique questions: https://drive.google.com/open?id=1b_wqd1iNlNICZmA9u8DjOReRXyt_5oBc