Best API-570 Exam Dumps for the Preparation of Latest Exam Questions
API-570 Actual Questions 100% Same Braindumps with Actual Exam!
API-570 is a certification program that is specifically designed for piping inspectors. Piping Inspector certification is offered by the American Petroleum Institute (API) and is recognized globally as a standard for the inspection and maintenance of piping systems. The API-570 certification exam evaluates the knowledge and skills of an individual in the field of piping inspection and provides them with a comprehensive understanding of the industry standards and practices.
API 570 certification is highly regarded in the industry, and it is a requirement for many piping inspector positions. It provides professionals with an opportunity to advance their careers and improve their earning potential. Professionals who hold this certification have demonstrated their knowledge and skills to inspect, repair, and maintain piping systems, which is essential to ensure the safety and reliability of these critical systems. Piping Inspector certification also provides employers with assurance that they have competent professionals on their team who can effectively manage their piping systems.
To be eligible for the API API-570 exam, candidates must have a minimum of three years of relevant experience in the field of piping inspection, as well as a high school diploma or equivalent. Additionally, candidates must meet certain educational and experience requirements, as outlined by the API. Once the exam is passed, the certification is valid for three years, after which the candidate must recertify to maintain their status as a certified piping inspector.
NEW QUESTION # 33
When an entire piping assembly is to be heat treated, but it will not fit into the furnace, what action should be taken?
- A. Radiograph the untreated area
- B. MT the untreated area
- C. Heat treat as much as possible and hardness test the untreated area
- D. Heat treat in more than one heat, with a 1" overlap
Answer: D
NEW QUESTION # 34
An inspector is evaluating a radiograph, a light image of a "B" appears on a darker background of the radiograph, the.
- A. radiograph shall be considered unacceptable
- B. "B" is for identification of the welder
- C. radiograph should not be rejected
- D. "B" is for identification of the weld
Answer: A
NEW QUESTION # 35
The preferred medium for pneumatic testing of small lines or systems is
- A. water
- B. air
- C. inert gas
- D. hydrogen
Answer: C
NEW QUESTION # 36
Which of the following best describes API 574?
- A. code
- B. specification
- C. Standard
- D. Recommended practice
Answer: D
NEW QUESTION # 37
Geometric unsharpness of the radiograph of a component under 2" th1ck shall not exceed
- A. 0.020"
- B. 0.050"
- C. 0.030"
- D. 0.040"
Answer: A
NEW QUESTION # 38
After hot bending and forming, heat treatment is required for which P numbers?
- A. 1,2,8,9A and 98
- B. 3,4,5, 6 and 10A
- C. 11ASG1 and 11ASG2
- D. 1, 2 and 7
Answer: B
NEW QUESTION # 39
When may welding not be performed?
- A. If the weld area is above 120° F
- B. If the weld area is in an inert atmosphere
- C. If the weld area is not in direct sunlight
- D. If the weld area is frosted or wet
Answer: D
NEW QUESTION # 40
An operator notice a pipe off its support, what should be done?
- A. Ignore the situation
- B. Keep a record of the situation for future reference
- C. Contact maintenance personnel for immediate repair
- D. Report the situation to engineering or inspection personnel
Answer: D
NEW QUESTION # 41
Of the following examples, which one may cause a leak in a threaded joint?
- A. Lack of thread lubricant
- B. Back welding the fitting
- C. Under pressuring the part
- D. Changing the direction of flow in the piping system
Answer: A
NEW QUESTION # 42
The minimum required pipe wall thickness or retirement thickness shall be based on pressure, mechanical and structural considerations using the appropriate design formulae and.
- A. nil-weight ductility stress
- B. CTOD stress
- C. code allowable stress
- D. assumption stress
Answer: C
NEW QUESTION # 43
A piping system started with a wall thickness of 0.375 inches. Over a five year period the wall thickness is now 0.1".
What is the long term corrosion rate?
- A. 550 Inches per year
- B. 0.055 inches per year
- C. Not enough information given
- D. 0.005 inches per year
Answer: B
NEW QUESTION # 44
Who is authorized to make a tack weld?
- A. A helper
- B. A fitter
- C. A qualified welder
- D. The welding foreman
Answer: C
NEW QUESTION # 45
When testing cast iron pipe which of the following methods should not be used?
- A. Leak test
- B. Ultrasonic test
- C. Hammer test
- D. Radiographic test
Answer: C
NEW QUESTION # 46
The radiograph of a Normal Fluid service piping weld revealed a crack.
What is the acceptable crack length if the pipe wall was 0.375?
- A. T/3
- B. 3/16"
- C. Cracks will not show on radiographs
- D. None
Answer: D
NEW QUESTION # 47
When an injection point circuit for the purpose of inspection is designated, the recommended up stream limit of the injection point circuit shall be the greater of ?
- A. minimum 12 inches
- B. maximum 12 inches
- C. three pipe diameters
- D. both A and C
Answer: D
NEW QUESTION # 48
What is the maximum length allowed for individual slag trapped in a weld in a Severe Cyclic Conditions piping system?
- A. >TW X 3
- B. 3/23"
- C. £TW / 3
- D. ³12T
Answer: C
NEW QUESTION # 49
The preheat zone shall extend beyond each edge of a pipe weld
- A. 2"
- B. 3T
- C. 1"
- D. 2T
Answer: C
NEW QUESTION # 50
A weld is changed from multi pass per side to single pass per side.
How does this effect the PWHT limitation?
- A. This limitation does not apply when a WPS is qualified with a PWHT above the upper transformation temperature
- B. This limitation does not apply when a WPS is qualified with a PWHT below the upper transformation temperature
- C. The PWHT is not a consideration
- D. The PWHT must be performed per ASME IX and time increased byone
Answer: A
NEW QUESTION # 51
A welder may be qualified by AT in any welding process except for which of the following?
- A. GMAW (spray arc mode)
- B. GMAW (short circuiting mode)
- C. SMAW
- D. FCAW
Answer: B
NEW QUESTION # 52
What is the working pressure of a 150 Ib. flange, SA 350 Gr.LF6 CL 1, used at 400°F?
- A. 170 psig
- B. 230 psig
- C. 140 psig
- D. 200 psig
Answer: D
NEW QUESTION # 53
The base metal is P.No.8, the weld metal is A . No.8-9, and the wall thickness is 1", what is the hold time for heat treatment
- A. ½ hour for each 1" thickness
- B. 1 hour
- C. None
- D. 2 hours
Answer: C
NEW QUESTION # 54
Penrtrameters (IQls) shall either be____or_____and shall be manufactured and identified in accordance with ASME.
- A. pica-type elite-type
- B. hole-type wire-type
- C. black-type white-type
- D. step wedge calibration block
Answer: B
NEW QUESTION # 55
The acronym CUI refers to.
- A. Carpet Under Infra-structure
- B. Cold Under-ground In-service piping
- C. Corrosion Under Inside flow
- D. Corrosion Under Insulation
Answer: D
NEW QUESTION # 56
With respect to a Class 400, NPS 12 slip on raised face flange, whose edges of the gasket do not extend to the bolt, what is the outside diameter of the gasket?
- A. 16.50"
- B. 15.00"
- C. 18.00"
- D. 12.75"
Answer: B
NEW QUESTION # 57
In the AWS D 5.1, what is the designation for cellulose DCEP electrode?
- A. E 6010
- B. E 6011
- C. E 7018
- D. E 7016
Answer: A
NEW QUESTION # 58
......
API-570 Study Material, Preparation Guide and PDF Download: https://www.testkingfree.com/API/API-570-practice-exam-dumps.html
Free API-570 Certification Sample Questions with Online Practice Test: https://drive.google.com/open?id=1mhNQKmRljrKgGxbiBdfdrs6CE0dqP8sC