H20-923_V1.0 Free Update With 100% Exam Passing Guarantee [2026]
[Aug-2026] Verified Huawei Exam Dumps with H20-923_V1.0 Exam Study Guide
NEW QUESTION # 35
When a critical alarm is generated in a lithium battery cabinet and the buzzer beeps continuously, the status of the indicator on the MDU is
- A. Steady yellow
- B. Blinking yellow fast
- C. Steady red
- D. Blinking red fast
Answer: D
Explanation:
In Huawei lithium battery cabinet alarm design, the MDU indicator and buzzer are coordinated to help O&M personnel immediately judge alarm severity without logging into a management system. Acritical alarmindicates that the battery system may no longer be in a fully safe or supported operating state and requires urgent handling, such as load protection actions, isolation, or immediate inspection. For this highest severity level, the cabinet uses the most prominent visual pattern:red with fast blinking, paired with acontinuous buzzer, to ensure the condition cannot be overlooked in an equipment room environment. Yellow indicators are reserved for lower severities such as warnings or minor/major alarms, where the system remains controllable and the required response can be scheduled. A steady red is typically used to indicate a persistent fault state or stop condition, whereasfast blinking red + continuous buzzeris the clear "critical, urgent" combination that triggers immediate on-site response and rapid fault localization (such as checking protection events, contactor status, temperature/voltage exceptions, and isolation conditions).
NEW QUESTION # 36
Which of the following models is a Huawei in-room chilled water horizontal air supply product?
- A. FusionCol5000-A050H
- B. FusionCol8000-C210H
- C. NetCol5000-A070U
- D. NetCol8000-C070D
Answer: A
Explanation:
Huawei room-level air conditioning products are commonly identified by the series name plus a model suffix that indicates the cooling medium and airflow form factor. Anin-room chilled waterunit uses a chilled-water coil as the primary heat-exchange component and relies on the building's chilled-water system (chiller/plant) rather than an onboard refrigeration compressor for cooling generation. "Horizontal air supply" describes the discharge direction: the unit supplies conditioned air laterally into the room or into a specific airflow organization (such as cold-aisle delivery), supporting predictable airflow paths and stable return air conditions. Within the provided options,FusionCol5000-A050His the model that matches both identifiers: it belongs to Huawei's room cooling product line and the model code indicates an in-room configuration withchilled-watercapability andhorizontalair supply orientation. The other options belong to different series or represent configurations typically associated with other deployment forms (such as different placement, airflow direction, or system architecture). Therefore, the correct selection isFusionCol5000-A050H.
NEW QUESTION # 37
Video management can connect to the third-party video surveillance subsystem and play historical videos.
- A. True
- B. False
Answer: A
Explanation:
In Huawei's data center O&M architecture, video is treated as an important auxiliary capability for security and remote operation. TheVideo Managementfunction is designed not only to view live camera feeds, but also to integrate video resources into the same O&M workflow as alarms, access control events, and environmental monitoring. In typical deployments, the actual video storage and recording are handled by athird-party video surveillance subsystem(for example, an NVR/VMS platform). Huawei's video management function can connect to that third-party subsystem so that camera resources can be accessed in a unified interface, allowing operators to perform linkage operations such as "view video on alarm" and routine security inspection without switching platforms. Because historical recordings are stored by the surveillance subsystem, once the integration is established and permissions are correctly configured, operators can retrieve andplay back historical videofor event tracing, audit, and incident investigation. This supports closed-loop O&M: alarm/event occurs # video verification # root-cause confirmation # maintenance action # evidence retention.
NEW QUESTION # 38
Which of the following are the user roles of Power Partner?
- A. DOC
- B. Service manager of a rep office
- C. Inventory operations manager
- D. Startup engineer
- E. Project manager
- F. Service engineer
Answer: A,B,C,D,E,F
Explanation:
Power Partner is Huawei Digital Power's partner service platform used to support delivery, commissioning, maintenance, and service operations across the full lifecycle of a project. To match real project workflows, the platform defines multiple user roles that align with different responsibilities and permission scopes. AStartup engineerfocuses on commissioning activities such as obtaining startup authorization, performing initial configuration, and completing functional verification. AService engineerhandles routine maintenance, inspections, troubleshooting, part replacement guidance, and closure of service cases. AProject managercoordinates delivery milestones, resource planning, and overall service execution to ensure acceptance criteria are met. AnInventory operations managermanages materials/parts flow, tracking, and availability to support timely repair and maintenance. TheDOC (Delivery/Dispatch Operations Center)role supports centralized operations such as work order dispatching, progress supervision, and process compliance.
Aservice manager of a representative officetypically oversees regional service quality, governance, and authorization control, ensuring the right people have the right access and that services are delivered according to Huawei process requirements.
NEW QUESTION # 39
Which of the following is the cabling mode of external power cables in IT scenarios of the FusionDC1000A?
- A. End wall cabling
- B. Top cabling
- C. Bottom cabling
- D. End door cabling
Answer: C
Explanation:
In the FusionDC1000A IT scenario, the external input power cables are designed to enter the power distribution system throughdedicated cable inlets at the bottomof the Power PDB. During installation, the procedure requires opening the Power PDB, removing the plugs from thebottom cable holes, and routing the external input power cables into the cabinet through these bottom entries before arranging them along the nearby cable support/bridge inside the Power PDB area. After the cables are terminated (for example, L1/L2
/L3/N and PE), the bottom cable entries are resealed using waterproof sealing materials to maintain enclosure protection performance. This bottom-entry method supports reliable mechanical routing for thick/armored power cables, reduces bending stress, helps maintain orderly segregation from signal cabling, and improves on-site safety by guiding high-current cables through a controlled inlet path. Therefore, the correct cabling mode for external power cables in FusionDC1000A IT scenarios isbottom cabling.
NEW QUESTION # 40
Operators can view parameters and set parameters on the "User Settings" and "Comm Settings" menus.
- A. True
- B. False
Answer: A
Explanation:
On Huawei data center cooling/monitoring controllers, menu permissions are typically organized so that routine O&M staff (operator role) can perform day-to-day adjustments that are required for normal running and integration, without accessing factory-only commissioning items. TheUser Settingsmenu is designed for operational configuration such as target temperature/humidity setpoints, control preferences, and other user- level parameters that need to be tuned to match the data hall environment and load changes. TheComm Settingsmenu is intended for communication configuration used in site integration, such as setting communication addresses, baud rates, protocol-related parameters, or enabling interfaces needed for upper- layer systems (for example, monitoring platforms). These settings are considered part of normal operation management and must be accessible so operators can maintain monitoring connectivity, replace controllers, or restore communication after changes. Higher-risk parameters (for example, factory calibration, protected control logic, or deep commissioning values) are normally restricted to higher privilege roles, but viewing and setting parameters withinUser SettingsandComm Settingsis an operator-allowed function.
NEW QUESTION # 41
Which of the following are main components of Huawei indirect evaporative cooling system?
- A. Compressor
- B. Fan
- C. Heat exchanger
- D. Spray system
- E. Air filter
- F. Water pump
Answer: B,C,D,E,F
Explanation:
Huawei's indirect evaporative cooling system is designed to use theoutdoor air as a "free" cold sourcewhile keeping the data hall supply air isolated from outdoor contaminants and moisture. Its core is theheat exchanger, where heat from the indoor (return) air side is transferred to the outdoor working air side without mixing the two air streams. To enhance heat removal on the outdoor side, aspray systemwets the evaporation media or spray section, and awater pumpcirculates water to maintain uniform wetting and stable evaporation performance.Fansdrive airflow through the indoor and outdoor paths to ensure sufficient heat transfer and maintain the required air volume and pressure. Because outdoor air is involved on the working-air side,air filtersare required to reduce dust and protect the heat exchanger and internal airflow channels, improving reliability and reducing maintenance. Acompressoris not a main component of indirect evaporative cooling because the system primarily relies on evaporation and heat exchange rather than mechanical refrigeration.
NEW QUESTION # 42
During wizard startup, when you enter the screen for selecting commissioning items for the first time, all items are selected by default. Which item is mandatory. You can deselect other commissioning items that are not mandatory.
- A. Commissioning the condensate pump
- B. Commissioning the indoor fans
- C. Commissioning the cooling system
- D. Commissioning the humidifier
Answer: C
Explanation:
In Huawei precision cooling commissioning, the wizard groups functional commissioning items so technicians can validate key subsystems efficiently. Thecooling system commissioningis mandatory because it verifies the primary control and protection loop that directly determines whether the unit can safely provide cooling capacity. This includes confirming the refrigeration or chilled-water cooling path can start and stop correctly, sensors and control logic are valid, and protection conditions (such as abnormal pressures
/temperatures, flow conditions, or interlocks) behave as expected. Without completing cooling-system commissioning, the unit's core purpose-stable temperature control for IT loads-cannot be assured, and the controller cannot reliably judge normal versus fault states during operation.
Other items (indoor fans, condensate pump, humidifier) are important butscenario-dependent: some sites do not use humidification, some drainage designs do not require an internal condensate pump, and fan checks can be handled as part of broader functional tests or may vary by redundancy configuration. Therefore, the wizard allows non-mandatory items to be deselected, but the cooling system commissioning must remain selected to complete a valid baseline commissioning workflow.
NEW QUESTION # 43
Huawei-developed intelligent rPDU (PDU2000M) can replace the original UIM20A expansion module. The rPDU can connect to the cabinet temperature/humidity sensors, smart U space managers, and door status sensors.
- A. True
- B. False
Answer: A
Explanation:
In Huawei smart module monitoring architecture, theUIM20A expansion moduleis traditionally used toincrease device portsso cabinets can connect multiple intelligent components and sensors (for example, door status and environmental sensors). Huawei also provides theintelligent rPDU PDU2000M, whosemain control moduleincludes communications and DI interfaces designed to directly##cabinet-level intelligent devices for centralized monitoring and management. In Huawei's solution description for rPDU-monitoring networking, thePDU2000M is positioned to replace the expansion-module role, meaning that in applicable scenarios, cabinets can connect monitoring devices through the PDU2000M without deploying an additional UIM20A expansion module. This supports practical connections such asT/H sensors,smart U space managers, anddoor status/door-access related signalsthrough the PDU2000M interfaces, and then these devices are managed
/bound in the controller's smart module view. Huawei O&M guidance also emphasizes avoiding duplicate connections (do not connect the same device to both UIM20A and PDU2000M), aligning with the replacement concept. (Scribd)
NEW QUESTION # 44
Which of the following statements are true about the routine maintenance of a UPS?
- A. If there is no alarm on the UPS panel, do not need to check the installation environment, temperature, and humidity onsite.
- B. Routine maintenance of vulnerable components: Periodically check the UPS fan operation, whether there is noise, and whether the rotation speed is abnormal.
- C. UPS status check: Check whether the UPS works in normal mode, whether an alarm is generated, and whether the UPS is in a proper load.
- D. Environment check: Check whether the temperature and humidity of the equipment room meet the recommended environment requirements. Check whether the equipment room is clean and tidy.
Answer: B,C,D
Explanation:
Routine UPS maintenance is preventive by design, so it must cover bothenvironmental conditionsandequipment operating status, not only alarms. The equipment room environment directly affects UPS reliability: high temperature accelerates capacitor aging, reduces battery/rectifier reliability, and may trigger derating; improper humidity increases the risk of condensation or electrostatic discharge; dust and poor housekeeping raise the risk of blocked airflow and overheating. Therefore, theenvironment checkin option A is a standard routine item. Option B is also essential because O&M personnel must confirm the UPS is innormal operating mode, verify no hidden alarms exist in the event log, and ensure the load level is within the recommended range to maintain redundancy and efficiency. Option C is true because fans are typical
"wear-out" components; abnormal noise or speed changes often appear before a failure and can be detected early through inspection. Option D is false: absence of a front-panel alarm never replaces onsite environmental inspection and basic preventive checks.
NEW QUESTION # 45
The NetEco service program backend can be accessed through the iBMC port.
- A. False
- B. True
Answer: A
Explanation:
In Huawei data center facility management,NetEcois the management software platform (server/application) used to centrally monitor and manage sites, whileiBMCis the out-of-band hardware management interface used forserver remote maintenance(such as power control, hardware health, BIOS settings, and remote console) on the specific server where iBMC exists. TheiBMC port is not a service access interface for NetEco. NetEco's backend services are accessed through theserver operating system network interfaces (management/service network) and corresponding application ports after the server is properly networked and configured. Even if NetEco is deployed on a Huawei server that has iBMC, iBMC only provides a channel to manage the server hardware and does not expose NetEco application access as an official commissioning
/O&M path. Therefore, NetEco backend access should be planned via the site's management network (IP addressing, routing, security policy), not via iBMC.
NEW QUESTION # 46
The software installation package does not need to be downloaded for the preinstalled server.
- A. True
- B. False
Answer: A
Explanation:
In Huawei delivery scenarios, apreinstalled servermeans the target software (for example, the NetEco platform and its required runtime components) has already been deployed and integrated on the server image before it is handed over for on-site commissioning. Because the installation media has already been applied, the on-site engineer's work typically shifts from "software installation" to "environment verification and initialization," such as confirming OS/service status, checking resource allocation, validating database and middleware health, verifying network planning (IP, gateway, DNS/NTP as required), and completing application-level initialization (site creation, user/role configuration, northbound interface settings, and device
/model import if needed). In this case,downloading the full installation package is not a mandatory stepfor commissioning, because the package is mainly required when performing a fresh installation or reinstall
/upgrade. However, standard practice is still to prepare supporting materials (patches, licenses, and compatibility documents) and ensure the preinstalled version matches the project baseline before acceptance.
NEW QUESTION # 47
The frequency of power supply equipment can be 50 Hz, 60 Hz, or 70 Hz.
- A. False
- B. True
Answer: A
Explanation:
In data center power systems, the utility grid frequency standard iseither 50 Hz or 60 Hz, depending on the country/region. Data center facility equipment-such as UPS systems, power distribution units, switchgear, and monitoring components-is designed to operate reliably under these standardized grid frequencies, with acceptable tolerance ranges around the nominal value. While some power conversion equipment can adapt between50/60 Hz(for example, via frequency tracking or double-conversion),70 Hz is not a standard utility frequencyused for data center facility power supply, and it is not treated as a normal operating frequency in typical design, acceptance testing, or O&M procedures. From an operations perspective, maintaining correct frequency is critical because abnormal frequency can trigger UPS transfer logic, increase losses, create synchronization issues with bypass sources, and negatively affect downstream IT loads. Therefore, stating that power supply equipment frequency "can be 50 Hz, 60 Hz, or 70 Hz" is incorrect for standard data center infrastructure practice.
NEW QUESTION # 48
Which of the following interfaces is used to connect the controller and the main control module of the unit?
- A. SW
- B. USB
- C. I2C/12v
- D. DP
Answer: C
Explanation:
In Huawei precision cooling units, the LCD controller (human-machine interface) must exchange real-time operating data and commands with the unit's main control module while also receiving a stable low-voltage power supply. This connection is typically implemented as alow-voltage communication bus plus DC power, which is why the interface is identified asI2C/12V. TheI2Cportion provides the data channel used for status display, parameter viewing/setting (within permission scope), alarm presentation, and command delivery (such as mute, reset, or control enable actions). The12 Vportion supplies power to the controller so it can operate independently of high-voltage power circuits and remain safe to access during routine O&M.
Interfaces likeDPandUSBare not used as the internal control link between the HMI and the main control board in this type of unit, and "SW" is not the designated controller-to-main-board interface in the standard wiring definition. Therefore,I2C/12Vis the correct selection.
NEW QUESTION # 49
Which of the following statements is false about the advantages of the free cooling solution for data centers?
- A. Directly uses the cooling capacity of the outdoor cooling source, resulting in ultra-low energy consumption.
- B. Has many use cases in the industry.
- C. The current technology is not mature enough and should be used with caution.
- D. Makes full use of the seasonal temperature difference of air and water sources.
Answer: C
Explanation:
Free cooling is a mainstream energy-saving concept in data center cooling design, used to reduce chiller compressor runtime by leveraging low outdoor temperatures (air-side) or low cooling-water temperatures (water-side) during suitable seasons. Therefore, describing the technology as "not mature enough and should be used with caution" is the false statement when discussing its advantages. In practice, free cooling has broad industry adoption and is considered a proven approach when applied with correct engineering, such as proper filtration, anti-condensation control, heat exchanger selection, and automatic control strategies. Its advantage is that it can directly utilize the outdoor "cold source" to remove heat, which significantly reduces cooling power consumption compared with full mechanical refrigeration, improving overall energy efficiency and supporting lower PUE targets. It also makes full use of seasonal and day-night temperature differences: the system dynamically switches among free cooling, partial free cooling, and mechanical cooling to balance reliability and efficiency. The key point is maturity: the benefit of free cooling comes from well-established principles and widely implemented architectures, not experimental technology.
NEW QUESTION # 50
Which of the following models is a Huawei in-room chilled water horizontal air supply product?
- A. FusionCol5000-A050H
- B. FusionCol8000-C210H
- C. NetCol5000-A070U
- D. NetCol8000-C070D
Answer: A
Explanation:
Huawei room-level air conditioning products are commonly identified by the series name plus a model suffix that indicates the cooling medium and airflow form factor. Anin-room chilled waterunit uses a chilled-water coil as the primary heat-exchange component and relies on the building's chilled-water system (chiller/plant) rather than an onboard refrigeration compressor for cooling generation. "Horizontal air supply" describes the discharge direction: the unit supplies conditioned air laterally into the room or into a specific airflow organization (such as cold-aisle delivery), supporting predictable airflow paths and stable return air conditions. Within the provided options,FusionCol5000-A050His the model that matches both identifiers: it belongs to Huawei's room cooling product line and the model code indicates an in-room configuration withchilled-watercapability andhorizontalair supply orientation. The other options belong to different series or represent configurations typically associated with other deployment forms (such as different placement, airflow direction, or system architecture). Therefore, the correct selection isFusionCol5000-A050H.
NEW QUESTION # 51
Which strategy most directly improves data center energy performance without compromising reliability when properly engineered and monitored?
- A. Disable alarms to reduce nuisance notifications and operator workload
- B. Use higher allowable supply air temperature with containment and adaptive control to reduce compressor and fan energy
- C. Oversize all cooling and power equipment permanently to avoid future upgrades
- D. Operate all redundant systems at full load simultaneously to maximize utilization
Answer: B
Explanation:
Huawei green data center concepts focus on reducing energy consumption through engineering controls rather than sacrificing resilience. Raising the allowable supply air temperature is a proven efficiency lever because it reduces compressor workload, expands economization opportunities where applicable, and can reduce fan energy when airflow is optimized. However, it must be implemented with airflow management-especially hot/cold aisle containment-to ensure server inlet temperatures remain within safe limits. Adaptive control is critical: monitoring rack inlet temperatures, cooling unit performance, and environmental conditions allows the system to dynamically adjust cooling output, fan speed, and setpoints to match real IT load. This avoids the common inefficiency of "overcooling for safety." When combined with standardized O&M procedures, alarm thresholds, and continuous trend analysis, the strategy improves overall energy performance while preserving reliability and service continuity. In contrast, permanent oversizing or forcing all redundant systems to run fully loaded wastes energy and can reduce operating efficiency. Properly engineered, monitored optimization delivers efficiency gains with controlled operational risk.
NEW QUESTION # 52
In IT scenarios, which of the following are the power supply and distribution components of the FusionDC1000A?
- A. Power PDB
- B. AC/DC power system
- C. SmartLi
- D. Integrated UPS
Answer: A,C,D
Explanation:
In the FusionDC1000A IT scenario, the power chain is built around an AC input, conditioned backup power, energy storage, and final distribution to the IT racks.Integrated UPSis the core power-conditioning component, providing voltage and frequency stabilization and uninterrupted supply during mains disturbances. The UPS works together withSmartLi, Huawei's lithium battery system, which serves as the energy storage unit to sustain the load during outages and to support controlled shutdown or generator switchover. After UPS output, power is delivered to the IT loads through thePower PDB, which performs downstream distribution, branch protection, and organized cable termination toward rack PDUs or IT equipment feeders. By contrast, anAC/DC power systemis typically associated with DC bus supply used in telecom-oriented or dedicated DC load scenarios, not the standard IT scenario architecture of FusionDC1000A that is centered on UPS plus battery plus AC distribution. Therefore, the correct components for IT scenarios are SmartLi, Power PDB, and Integrated UPS.
NEW QUESTION # 53
After the unit is powered on for the first time, it enters the compressor preheating state. To quickly perform power-on commissioning, you can manually shut down the compressor preheating.
- A. False
- B. True
Answer: A
Explanation:
Compressor preheating is a protection mechanism used during first power-on (and after long power-off periods) to improve compressor reliability before allowing refrigeration startup. The preheating function warms the compressor oil and reduces refrigerant migration and oil dilution, which otherwise can lead to liquid refrigerant in the compressor crankcase. If the compressor starts when oil is diluted or when liquid refrigerant is present, it increases the risk of abnormal noise, poor lubrication, high mechanical stress, and even liquid strike, which can damage the compressor and shorten service life. For data center cooling equipment, where continuous reliability is essential, the commissioning logic treats preheating as a required prerequisite for safe compressor operation. Therefore, O&M practice does not recommend bypassing or manually shutting down compressor preheating just to accelerate commissioning. The correct approach is to keep the unit energized and allow the preheating period to complete, then proceed with commissioning steps (fans, cooling system tests, alarms, and control verification) under proper protection conditions.
NEW QUESTION # 54
What is the upstream input voltage range of the UPS5000-H?
- A. 220 V-240 V
- B. 360 V-600 V
- C. 138 V-485 V
- D. 380 V-415 V
Answer: C
Explanation:
For the Huawei UPS5000-H (380/400/415 V class), "upstream input voltage range" refers to the acceptableAC mains (rectifier) line-to-line input voltage windowthat the UPS can tolerate while maintaining operation. Huawei specifies a wide mains input voltage range of138-485 Vac (line voltage)to improve adaptability to weak or fluctuating power grids and to reduce unnecessary battery usage when the utility voltage sags or rises within allowable limits. Within this overall window, the UPS may applyderating rulesat lower voltages (for example, full-load operation is typically guaranteed only above a higher threshold), but the upstream input can still remain connected and the UPS continues supplying the load according to its control strategy and available capacity. The other options do not match the upstream AC input range:360-600 Vis commonly associated withbattery DC voltage ranges,220-240 Vis single-phase class, and380-415 Vrepresentsrated voltage, not the full acceptable upstream range.
NEW QUESTION # 55
The NetEco northbound interface does not support the SNMP protocol. Only WebService interfaces are supported.
- A. False
- B. True
Answer: A
Explanation:
In Huawei's data center facility management architecture, thenorthbound interfaceof NetEco is designed specifically to integrate with upper-layer systems such as enterprise NMS platforms, SOC/monitoring centers, and customer unified O&M systems. To meet common industry integration practices, NetEco northbound capabilities are not limited to only one interface type. In addition to WebService-style interfaces used for richer data exchange and structured integration, NetEco also supportsSNMP-based northbound integration, which is widely used for alarm forwarding, basic status monitoring, and interoperability with standard network management tools. SNMP is particularly common in mixed-vendor environments because it enables a lightweight and standardized method to deliver key alarms and events to a customer's central monitoring platform without requiring deep application coupling. Therefore, the statement that "only WebService interfaces are supported and SNMP is not supported" is incorrect: NetEco northbound integration supports SNMP along with other northbound interface methods depending on the integration scenario and customer requirements.
NEW QUESTION # 56
The NetEco supports manual backup and automatic backup.
- A. True
- B. False
Answer: A
Explanation:
NetEco is a management platform that stores critical operational data, including site configuration, device models, user/role information, historical alarms, trend data, reports, and northbound integration settings. To protect these assets and ensure service continuity, NetEco provides a built-in backup mechanism that supports bothmanualandautomaticbackup modes.Manual backupis typically used before major operations such as version upgrades, configuration changes, northbound interface adjustments, or large-scale device onboarding, so engineers can create a restore point on demand.Automatic backupis used for routine risk control and is normally implemented through scheduled tasks, allowing backups to be generated at defined intervals to reduce data-loss exposure in case of hardware failure, system corruption, or accidental misconfiguration. In standard O&M practice, automatic backups are combined with retention policies (for example, keeping a rolling set of backup files), storage capacity checks, and periodic restore verification to confirm backup integrity. This dual-mode backup capability is a foundational requirement for stable long-term operation of management systems like NetEco.
NEW QUESTION # 57
Which of the following are the user roles of Power Partner?
- A. DOC
- B. Service manager of a rep office
- C. Inventory operations manager
- D. Startup engineer
- E. Project manager
- F. Service engineer
Answer: A,B,C,D,E,F
NEW QUESTION # 58
When a critical alarm is generated for the unit, the indicator on the LCD controller turns red and the buzzer beeps continuously.
- A. True
- B. False
Answer: A
Explanation:
In Huawei data center facility equipment (such as precision cooling units and related controllers), alarm presentation follows a clear severity-based design so technicians can recognize urgency immediately without entering detailed menus. Acritical alarmrepresents the highest severity level and is treated as a condition that may impact safe operation, cooling continuity, or equipment protection. For this reason, the LCD controller uses the most prominent visual and audible indications: theindicator turns redto show critical severity, and thebuzzer sounds continuouslyto ensure the alarm cannot be overlooked in a noisy equipment-room environment. This behavior supports rapid response: O&M personnel can quickly identify that immediate action is required, then open the alarm list to locate the root cause, confirm whether the unit has derated or stopped, and execute the prescribed troubleshooting steps (for example, checking power status, sensor readings, fan/compressor status, water flow/pressure, and protection interlocks). Therefore, the statement correctly describes the standard critical-alarm indication method on the LCD controller.
NEW QUESTION # 59
Which O&M practice is most effective for identifying cooling inefficiency caused by airflow problems in an operating data center?
- A. Disable temperature sensors to prevent false alarms
- B. Lower supply air temperature to the minimum possible value at all times
- C. Compare rack inlet temperatures, return air temperatures, and fan speed trends to detect recirculation and bypass
- D. Run humidification continuously regardless of ambient conditions
Answer: C
Explanation:
Huawei facility O&M methods emphasize using monitored operating data to locate inefficiencies before they become faults. Airflow-related cooling inefficiency commonly appears as hot spots at rack inlets, elevated return air temperature fluctuations, abnormal fan speed increases, or uneven temperature distribution across aisles. By trending rack inlet temperature sensors alongside cooling unit supply
/return temperatures and fan speed or airflow commands, operations teams can distinguish between insufficient cooling capacity and poor airflow organization. Recirculation (hot air returning to rack inlets) often raises localized inlet temperatures without a proportional rise in room average temperature, while bypass (cold air short-circuiting back to returns) reduces cooling effectiveness and can drive fans to higher speeds unnecessarily. Data-driven checks support targeted corrective actions such as sealing cable openings, adjusting floor tile placement, restoring containment integrity, balancing airflow, or optimizing setpoints. This approach improves thermal stability, prevents overcooling, reduces energy waste, and aligns with Huawei's emphasis on integrated monitoring and closed-loop optimization for reliable, efficient operation.
NEW QUESTION # 60
......
Authentic Best resources for H20-923_V1.0 Online Practice Exam: https://www.testkingfree.com/Huawei/H20-923_V1.0-practice-exam-dumps.html
H20-923_V1.0 Test Engine Practice Exam: https://drive.google.com/open?id=18MJEygoP22AzSoB43MsBa_BacZuZv9vY